SkyLink MK-1 Bedienungsanleitung PDF herunterladen

1. INTRODUCTION

Model MK-1

Universal Garage Door

Remote Control

Congratulations on your purchase of MK-1, the package includes Skylink

garage door receiver -Smart Button

GB-318, and Skylink

garage door

transmitter - remote control MK-318. In this package, you will find the

following:

Crimper

Garage Door

Transmitter

MK-318

(Battery inside)

Unplug the power cord of your garage door opener before installation to ensure

power is not connected.

DO NOT let children use the gargae door Transmitter without adult supervision.

Children can injure themselves or others by the garage door.

DO NOT use remote to control the door without safety beams.

WARNING

1. Open up the “Easy Clip

” and place it underneath

the existing 2 wires of the wall button / wall

console.

2. Ensure a pair of the wall button ribbon wires

are placed properly inside the channels of the

“Easy Clip

”.

NOTE:

Ensure the ribbon wires

are not twisted but laid

flat inside the clip.

If your wall button ribbon wires

are not the same kind as shown

in the diagram, please refer

below (4) or visit our website

www.skylinkhome.com or

Easy Clip

Ribbon Wires

Wall Button

Ribbon Wires

Press / lock

3. Press and lock the clip by

snapping it together. The

included Crimper helps you

lock the “Easy Clip

”. Close

the cover and press down

to lock the cover using this

Crimper until you hear a “click”.

4. If the Easy Clip

” cannot clip the wires from your wall button, cut

off the Easy Clip

” then connect two wires from the Smart Button

GB-318 to the wall button.

a) Disconnect the existing wall button from the wall.

b) Connect the 2 wires from the Smart Button

GB-318 to your existing wall button. Polarity does

not matter, so simply pick one wire from the Smart

Button

GB-318 and connect it to one of the

screw terminals on your wall button. Connect

the 2nd wire to the other screw terminal.

c) Reconnect the wall button back.

Rating of the transformer:

12V DC, 100mA

Diameter of DC plug : 3.5mm

7. Secure the SmartButton

GB-318 properly with the mounting accessories.

Note: Do not cut the antenna!

Straighten up the antenna to improve

signal reception.

5. If the wall button wires are hidden inside the

wall, please connect the “Easy Clip

” to

the exposed wires attached to the

terminals of the garage door

opener.

You need to do the programming in order to add the transmitter to a receiver.

3. PROGRAM TRANSMITTER MK-318 TO RECEIVER GB-318

Smart Button

GB-318 can learn up to sixteen single button

transmitters or keypads or five 3-button transmitter .

To add remote controls, follow the instructions below:

1. Press the learn button on the side of the Smart Button

GB-318.

2. Once the learn button is pressed, the LED will

flash quickly. Release the learn button.

3. Within 30 seconds, press any one of the 3 buttons on

the transmitter that you want to program to the receiver.

4. Once the remote control is programmed, the LED

will flash slowly, in the same way as it flashes

in standby mode.

5. You may now operate the garage door opener

with this new remote control.

6. To program this transmitter to control another

receiver, repeat process (1) to (4) to program

another button on the remote control.

If the red LED flashes slowly, the Smart Button

GB-318

is in standby mode. When a valid remote control signal is

received, it will open / close the garage door.

Press the programmed button on the remote control

or Smart Button

GB-318, it will open / close the

garage door.

OPEN /

Button

4. OPERATION

Double Sided Tape

2. RECEIVER INSTALLATION

Note: After installation of the “Easy Clip

”, if you want to re-install the

Smart Button

GB-318 to another place, please open the “Easy Clip

” by

gently unlocking the two buckles with a screw driver, and remove it from

the wires. Do not re-use the “Easy Clip

”, refer to Step 4 to re-install it.

LED

Garage Door

Receiver

Smart Button

GB-318

Connect the receiver - Smart Button

GB-318 to your current garage

door opener system, you can use the transmitter - remote MK-318 to

open or close the garage door.

To erase unwanted remote control(s)from the memory of Smart Button

GB-318, first erase all remote controls, then learn the one(s) you would

like to keep, follow the steps below:

1. Press and hold the learn button for approximately 10 seconds.

2. The LED will flash rapidly after 10 seconds to indicate all the pro-

grammed remote controls have been erased. You may now release

the learn button.

3. You have erased all the remote controls programmed to the Smart

Button

GB-318.

5. ERASE TRANSMITTERS

6. TROUBLE SHOOTING

Q: What can I do if the door opener does not react after I press the button on

the transmitter ?

A: - Ensure when the button on the transmitter is pressed, the red LED on the

transmitter comes on. Otherwise, check if the battery is inserted properly.

- Make sure the correct button on the transmitter is pressed.

- Ensure the wires that were previously connected to the wall mounted

door control are not loose.

- Ensure the transmitter has been programmed to the receiver. Refer

to section 2 for how to program a transmitter to the receiver.

6. Power up the garage door opener, the red LED on the Smart Button

GB-318 should keep flashing slowly for 2 minutes.

2. RECEIVER INSTALLATION (CONT)

If the Smart Button

GB-318’s red LED does not flash after the

Smart Button

GB-318 has been connected to the wall button’s

wires for 2 minutes, your garage door opener is probably too

old. However, the Smart Button

GB-318 will still work if you

plug in an adapter (purchased separately). Please

contact Skylink

to purchase the adapter.

Push Button

Terminals

Learn

Smart Button

LED

1 2

Inhaltsverzeichnis

Seite 1 - Remote Control

1. INTRODUCTIONModel MK-1Universal Garage DoorRemote ControlCongratulations on your purchase of MK-1, the package includes Skylink®garage door receive

Seite 2 - Password protection

You can add up to sixteen single buttontransmitters or keypads or five 3-buttonadditional transmitters or keypad to control theGB-318. Skylink® offer

Kommentare zu diesen Handbüchern

Keine Kommentare

SkyLink MK-1 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Garagentor-Öffner SkyLink MK-1 herunter. SkyLink MK-1 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Garagentor-Öffner SkyLink MK-1