Skylink G6KR Bedienungsanleitung PDF herunterladen

1. INTRODUCTION

Model G6KR

Garage Door

Remote Control

2. INSTALLATION

Unplug the power cord of your garage door opener

before installation to ensure power is not connected.

WARNING

GTR Smart Button

The GTR Smart Button

replaces most garage door “push buttons”

or “wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener comes equipped with a single button “push

button”, you can replace the existing push button with Skylink

Smart

Button

GTR. Please follow the procedures below.

1. Remove the existing push button by removing

the screws.

2. Disconnect the 2 wires that are connected to

the existing push button.

3. Connect the 2 wires from the existing wall

button to the GTR Smart Button

. Twist the 2

wires together with the wire connector

provided. Polarity does not matter, so simply

pick one wire from the existing wall button, and

connect it to one of the wires on the Smart

Button

. Do the same for the 2nd wire.

4. After connecting the wires, mount the Smart

Button

on to the wall with 2 screws.

5. Plug in the AC cord of the garage door opener.

The red light on the Smart Button

should flash

15 seconds after plugging in the power. The

red light will not flash immediately after

plugging in the power, which is normal. The

Smart Button

is now ready to be operated.

Note: Straighten up the antenna to improve signal reception.

Remove

existing

wires

Mounting

Accessories

2. INSTALLATION (CONT)

Smart Button

2) Multi-Function Wall Console

Multi-Function Wall Console normally comes with 3 buttons that can be

used to:

1) operate the garage door opener lighting,

2) lock the receiver so it doesn’t accept

remote control operation, and

3) push button for door opening / closing

Congratulations on your purchase of the Skylink

G6KR Universal

Garage Door Remote Control. This is a kit with a universal keypad

transmitter and Smart Button

. It is 100% compatible with all garage

door openers. Simply replace the traditional wall button by the Smart

Button

, that’s all for the installation. In this kit, you will find the

following:

Rating of the transformer: 12V DC, 100mA

Diameter of DC plug : 3.5mm

Note: Straighten up the antenna to improve signal

reception.

If you have the multi-function wall console, do not replace the wall

console by the Smart Button

. You need to install the Smart Button

parallel with your existing wall console.

1. Remove the existing wall console from the wall

by removing the screws.

2. Remove the 2 screws that secure the wires

on the wall console.

3. Connect the wires from the Smart Button

to the

existing wall console. Polarity does not matter,

so simply pick one wire from the Smart Button

and connect it to one of the terminals on the

existing wall console. Do the same for the 2nd

wire.

4. After connecting the wires, mount the Smart

Button

on to the wall with 2 screws. Also

mount the original wall console on to the wall.

5. Plug in the AC cord of the garage door opener.

The red light on the Smart Button

should flash

15 seconds after plugging in the power. The red

light will not flash immediately after plugging in

the power, which is normal. The Smart Button

is now ready to be operated.

6. If the Smart Button

red light does not flash at

all 2 minutes after plugging in the AC cord, your

garage door opener is probably too old.

However, the Smart Button

will still work by

plugging in an adapter (purchase separately).

Please contact Skylink

to purchase the

adapter.

If the red light on the Smart Button

is flashing slowly,

that indicates it is in standby mode. When a valid

remote control signal is received, it will open / close the

garage door.

Simply press the button on the Smart Button

, it

will open / close the garage door.

OPEN /

3. OPERATION

Antenna

2 Wire

Connectors

Universal

Keypad Transmitter

(Battery included)

- To change your PIN:

1. Enter the current PIN, (currently set at 0 0 0 0), press ,

2. Enter new 4 digit PIN, press ,

3. Enter new PIN again, press .

For example, if you are changing the PIN number from 0000 to 1234,

enter the following sequence, 0000, ,1234, ,1234, .

If confirmed, the backlit LED flashes and the unit emits a long beep.

- Operation

Press [ PIN ] , [#] To open or close garage door, press your four digit

PIN and the [#] key. If confirmed, the keypad transmitter will emit three

beeps.

Default PIN is 0000.

Press [0000][#] to open the garage door.

If you do not hear 3 beeps after the 4-digit PIN and [#] is entered, that means

you have entered an incorrect PIN, and the keypad transmitter will not

operate your garage door.

1 2

Inhaltsverzeichnis

Seite 1 - Remote Control

1. INTRODUCTIONModel G6KRGarage DoorRemote Control2. INSTALLATIONUnplug the power cord of your garage door openerbefore installation to ensure power i

Seite 2 - Programming

Erase remote controlsTo erase unwanted remote control(s), first erase all remote controls,then learn the ones you would like to keep.To erase remote c

Kommentare zu diesen Handbüchern

Keine Kommentare

Skylink G6KR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Küche Skylink G6KR herunter. Skylink G6KR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küche Skylink G6KR